Airless Road Marking Machine CMC AR30ITP 3-WHEEL WITH HYDRAULIC DRIVE WITH VARIABILE FLOW PUMP
SPRAYABLE PAINTS: monocomponent not refractive paints (=without premixed glass beads) solvent based or waterborne paints, paints with specific formulation for airless machines with 70-75 KU viscosity at 20⁰C. Solvent based or waterborne epoxy paints. Polyurethane paints
SUITABLE FOR: indoor markings, on concrete surfaces. For small road marking jobs, parking lots, sports fields, cycle lanes. Jobs involving frequent colour changes
Plastic container for paint: capacity 30 l.
Container is replaceable with paint bucket (max.
diam. 32 cm)
Airless diaphragm pump:
-max. working pressure 210 bar
-max. delivery 5,9 l/min
Single-stage single-cylinder compressor:
-flow air rate 215 l/min
-with pressure limiting valve
Automatic paint gun. Standard nozzle for 10-20 cm
line. (Line width can be ranged from 5 cm to 30 cm
by changing nozzle and adjusting gun height)
Gun support with wheel: to follow the road.
(Support can be replaced with pneumatic support.
Look at optional)
MAX. LINE WIDTH: 50 cm
(achievable only with proper optional equipment)
Gasoline engine:
-power 7 HP
-self-winding pull start
-centrifugal pulley
Hydraulic drive with:
-2 motors directly coupled on rear wheels
-hand-grip control: controls forward, reverse and neutral gear
-VARIABLE-FLOW PUMP: guarantees more safety for operator and
better performance. Allows to overcome steep slopes
Parking brake on rear wheel
Swivel front wheel with stabilizer springs, to stripe very sharp curves.
It can be locked or unlocked during the work by a pneumatic control
on dashboard. It's also possible to totally remove springs and adjust
steering hardness by proper regulator
Telescopic pointer for easily following pre-marking or precisely
matching existing line
Engine shut-off safety device if operator leaves the handlebars
Machine is equipped with all safety devices according to EU requirements.
Machine conforms to:
* EU Directive 2006/42/EC on Machinery
* EU Directive 97/23/EC for Pressure Equipment (PED directive)
OPTIONAL EQUIPMENT:
- Electric starting
- Light, for night works.
Attention: can be used only if striper is equipped with optional Electric starting
- Turning light, for a better visibility of operator on the street.
Attention: can be used only if striper is equipped with optional Electric starting
- Electronic spacing device C8000 with:
possibility to select 8 different skip line patterns
possibility to record: total metres made (paint+space); total metres striped (only paint); total metres striped (only paint)
by each gun
sound speed alarm: rings when operator works outside range of minimum speed and maximum speed. Min. and max.
speeds are adjustable. (Maintaining constant speed is important for getting uniform paint film).
Attention: Electronic spacing device can be used only if striper is equipped with optional Electric starting
- Trailer with standing driver
- Second automatic paint gun with independent control, to stripe 50 cm or 2 lines at the same time (for example continuous
line + skip line)
- Pneumatic support for paint gun (one disc), to keep automatic gun always at the same distance from ground, ensuring
constant width of the line
- Manual paint gun-short with 10 m hose, for stenciling (SUGGESTED OPTIONAL)
- Manual paint gun -long (with extension 45 cm) with 10 m hose, for stenciling without bending and standing farther from paint
spray
- Glass bead dispenser (SUGGESTED OPTIONAL) consisting of:
glass bead tank. Available: - gravity glass bead tank, capacity 15 l
- pressurized glass bead tank capacity 15,5 l
automatic glass bead gun with adjustable diffuser
closing delay regulator for bead gun
- Second automatic glass bead gun with independent delay regulator.
Attention: can be used only if striper is equipped with optional Glass bead dispenser
- Manual glass bead gun with air hose and bead hose, for bead application on stenciling.
Attention: can be used only if striper is equipped with optional Glass bead dispenser
We suggest to complete the machine equipment with:
- nozzle for line width 5 cm
- nozzle for line width 30 cm
- nozzle for surfaces, advised for stenciling (crosswalk, symbols, legends, stops, …).
Български
Русский
Român
Ελληνικά
Italiano
Deutsch
Write a review: